Aleco Clear-Flex II with MaxBullet Mounting System Manual do Utilizador descarregar pdf (Página 1)

FOR ANY QUESTIONS OR COMMENTS, PLEASE CONTACT AN ALECO REPRESENTATIVE

2720 E. Avalon Ave. Muscle Shoals, AL 35661 ● Phone (256) 248-2402 or toll free 1-800-633-3120

Fax: 1-800-750-9616 ● email: info@aleco.com ● web: www.aleco.com

P/N 477248

1110

Diagram 1

Under Header (Lintel) Position

Wall

Fastener Supplied by

Others

MaxBullet

Hardware

Bracket

Bullet

Strips

Diagram 2

Wall (Header) Position

Wall

Fastener Supplied

by Others

MaxBullet

Hardware

Bracket

Bullet

Strips

Diagram 3

Front View Strip Spacing

Clear-Flex

II Strip Door

Installation Instructions

Using the Maximus System

Hardware

TOOLS NEEDED

• Pen or Pencil to Mark Drill Holes *

• Drill

• 5/16” Diameter Fasteners

• Step Stool or Ladder

• Utility Knife to Cut Strips

IMPORTANT

Prior to installation, unroll all door strips and place them on

a clean, flat surface in a warm atmosphere for a minimum of

twenty-four (24) hours. This will allow the strips to return to

their original form.

1. Mount the MaxBullet

hardware bracket in

either the under header or wall position

shown in Diagrams 1 and 2 using

appropriate fasteners supplied by others

(recommended 5/16” diameter).

2. Press the door strips onto the “bullets” of the

hardware bracket making certain that the

concave sides are facing each other

(Diagram 4). Attach strip numbers 1 and 3

(see Diagram 3) with concave side toward

you, leaving desired spacing between strips

as indicated by the diagram on reverse side

of this sheet.

Diagram 4

3. Attach strip number 2 with concave side

away from you over strip numbers 1 and 3

(Diagram 3).

4. Attach all of the remaining door strips in the

same manner as in Steps 2 and 3 making

certain that the concave sides face each

other (Diagram 4).

5. Once all of the door strips have been

attached, the strips can be trimmed to leave

¼” of clearance from the floor surface. Your

PVC door strips may be trimmed by using a

common utility knife to score and then be

torn by hand. The door strips need to

hang for 24 to 48 hours before final trim

to allow for proper alignment.

* NSF certification applies when hardware is installed with approved low-temp PVC strip material.

1 2

Resumo do Conteúdo

Página 1 - Installation Instructions

FOR ANY QUESTIONS OR COMMENTS, PLEASE CONTACT AN ALECO REPRESENTATIVE 2720 E. Avalon Ave. Muscle Shoals, AL 35661 ● Phone (256) 248-2402 or toll fre

Página 2 - STRIP PLACEMENT GUIDE

STRIP PLACEMENT GUIDE PARTIAL OVERLAP FULL OVERLAP FULL OVERLAP 100% 6” WIDE MATERIAL PARTIAL OVERLAP 66% PARTIAL OVERLAP 50%8” WIDE

Comentários a estes Manuais

Sem comentários

Aleco Clear-Flex II with MaxBullet Mounting System Manual do Utilizador Página 1

Consulte online ou descarregue Manual do Utilizador para Ferramentas Aleco Clear-Flex II with MaxBullet Mounting System. Aleco Clear-Flex II with MaxBullet Mounting System User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Aleco Clear-Flex II with MaxBullet Mounting System Manual do Utilizador Página 1

Consulte online ou descarregue Manual do Utilizador para Ferramentas Aleco Clear-Flex II with MaxBullet Mounting System. Aleco Clear-Flex II with MaxBullet Mounting System User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Ferramentas Aleco Clear-Flex II with MaxBullet Mounting System